Bascule Bridge at North Tonawanda

One of the most interesting and challenging structures that I will have to build for my layout depicting the town of North Tonawanda is the bascule bridge over the barge canal. The bridge was built as part of a track re-alignment project undertaken by NYC between 1917 and 1922. The bridge carried the NYC Niagara Branch, double-track at this point, which was NYC’s direct connection between Niagara Falls NY and Buffalo NY.

An interesting fact about the bridge is that it was only opened once. It seems that a government transportation authority insisted on provisions for the expansion of the barge canal to accommodate higher vessels. In response, NYC built a bascule bridge instead of a fixed structure. I’m told that on the day the bridge was put into service, there were some dignitaries present to witness the opening and closing of the bridge. It was never opened again.

The bridge is oriented north-south. To the south of the bridge, the Lehigh Valley gained access to the NYC Niagara Branch which LV used to access its own yard in Niagara Falls NY. The small NYC yard and connection to the paper plant at North Tonawanda are about a half-mile north of the bridge.

I photographed the bridge in 2013. After studying the bridge, I decided against building a model of it, on the grounds that it would be too difficult. Lately, I’ve been reconsidering my previous position because it is the single most identifiable landmark that establishes the setting of my layout. Without it, visitors might simply have to take it on faith that the layout represents North Tonawanda. With that in mind, I’m gearing up to have a go at it. Having never scratch-built a structure like this, I’m spending some time thinking about how to approach it. So far, my friend Chris Vanderheide is helping me plan the build. I can use all the help I can get.

Here are a few of my photos of the bridge. They provide a general overview of the structure’s layout.

IMG_2342

Looking east along the Erie Canal.

In the first photo, above, I can see some basic sub-structures that might simplify construction. The concrete pier in the barge canal is the hinge point of the bridge. The truss on the right is the part that lifts, so it’s rigid. The apex of the triangle to the left of the hinge on the pier provides the fulcrum between the concrete counterweight and the rigid truss that draws upwards.

Taken from the north side of the canal, looking at the west side of the bridge, minus the counterweight.

Taken from the north side of the barge canal, looking at the west side of the bridge, minus the counterweight.

Taken from the north side of the canal, west side of the bridge, looking up at the concrete counterweight.

Taken from the north side of the canal, west side of the bridge, looking up at the concrete counterweight.

At north and south ends of the bridge, there are short deck girder bridges that carry the tracks over roads that parallel the barge canal on both sides. The tracks approach the bridge on large earth fills from the north and south. On the north side of the canal, the North Tonawanda side, the fill provides a convenient grade separation for a couple of residential streets, which I also plan to model.

I have plenty of photos of the general layout of the bridge, but these show the overall structure. I believe what stands ahead of me is an estimation of the overall dimensions of the structure so that I can decide whether to compress it or build it proportionally.

I recognize this as a long-shot, but if anyone has information pertaining to this bridge, I’d love to have access to it. Drawings would, of course, be ideal, but anything else would be helpful and greatly appreciated, including how NYC and Penn Central managed rail traffic in the area around the bridge. I’m also interested in advice on how plan for and undertake this project. I’m looking forward to hear what you have to say.

Deck Truss Bridge

I put together this 75 foot deck truss bridge from an old Juneco kit.  This is one of those models that I undertook for the sheer enjoyment of building.

Excuse the ugly setting for the photos.  I tried to block out background distractions with a green tote lid.  Plus I had a mishap with black paint on my cutting surface.  Bush league, I know.

IMG_2414

IMG_2410

The parts were stained before assembly and I did some basic weathering when it was finished.  The weathering kind of matches my backyard table 🙂

The photo below shows the bridge on its side with the steel rods, bearing plates, and nut/bolt castings painted Polly Scale Rust straight from the bottle.  This is meant to be a primer for subsequent layers of rust.

IMG_2415

I have no idea of the prototype for this bridge, so if anyone can enlighten me, please do.

Underside view

Underside view

I enjoyed putting it together so much that I lost track of the hours that went into it.  It was a fun build, which was why I did it.  I’ll probably sell it because I don’t foresee being able to put it to use.